Download and Install IBM DS Storage Manager 10 for Windows Server 2003/2008 (64-bit) in 10 Easy Steps
Download IBM DS Storage Manager 10
Introduction
In this article, you will learn what is IBM DS Storage Manager 10, why you need it, and how to download it for your Windows Server 2003 or 2008 (64-bit) operating system. You will also learn how to install, configure, and use the software to manage your IBM System Storage DS3000 series devices.
Download Ibm Ds Storage Manager 10
What is IBM DS Storage Manager 10?
IBM DS Storage Manager 10 is a software application that allows you to perform logical configurations and copy services management functions for your IBM System Storage DS3000 series devices. It provides a graphical user interface (GUI) and a command-line interface (CLI) that let you monitor, configure, and manage your storage subsystems and logical drives.
Features and benefits of IBM DS Storage Manager 10
Some of the features and benefits of IBM DS Storage Manager 10 are:
It supports multiple storage subsystems and hosts.
It allows you to create, modify, delete, and view arrays, logical drives, host ports, mappings, and premium features.
It enables you to perform copy services operations such as volume copy, flash copy, remote mirror, and enhanced remote mirror.
It provides event notification and logging capabilities.
It supports IPv6 and Telnet protocols on the controller management Ethernet ports.
It offers a pre-read redundancy check feature that verifies the redundant RAID data consistency before returning the requested read data back to the host.
It allows you to import and export arrays between different storage subsystems.
It enables you to configure a hot spare or an unassigned drive as a permanent member of an array.
It performs an advanced controller cache battery learn cycle that determines the full recharge capacity of each battery.
It collects a support bundle on critical events that can be used for troubleshooting purposes.
Why do you need IBM DS Storage Manager 10?
If you have an IBM System Storage DS3000 series device, such as DS3200, DS3300, or DS3400, you need IBM DS Storage Manager 10 to manage your storage subsystems and logical drives. You can use the software to perform various tasks such as creating arrays and logical drives, assigning host ports and mappings, enabling premium features, performing copy services operations, monitoring the status and performance of your storage subsystems and logical drives, configuring event notification and logging settings, updating firmware and device drivers, importing and exporting arrays, performing diagnostics and troubleshooting, and more.
How to download IBM DS Storage Manager 10?
To download IBM DS Storage Manager 10 for your Windows Server 2003 or 2008 (64-bit) operating system, you need to follow these steps:
Go to the [IBM Support](^1^) website.
In the search box, type "IBM DS3000 Storage Manager v10.35.35.40 for Microsoft Windows Server 2003/2008 (64-bit)" and click Search.
From the search results, click on the link that matches the title above.
You will see a page with file details, change history, download description, severity level, prerequisites, installation instructions, uninstallation instructions, limitations and known issues, trademarks information, contact information, etc.
To download the file ibm_sw_ds3k_10353540_winsrvr_x86-64.zip (244 MB), click on the file link under File link column.
You will be prompted to sign in with your IBM ID or create one if you don't have one already.
After signing in, you will see a license agreement page. Read the terms carefully and click on I agree if you accept them.
You will see a download options page. Choose your preferred method of downloading (HTTP or Download Director ) and click on Download now.
You will see a download progress page. Wait for the download to complete or use a download manager to resume the download if it is interrupted.
After the download is complete, you will see a confirmation page. Click on Close to exit the page.
How to install IBM DS Storage Manager 10?
To install IBM DS Storage Manager 10 on your Windows Server 2003 or 2008 (64-bit) operating system, you need to follow these steps:
Extract the downloaded file ibm_sw_ds3k_10353540_winsrvr_x86-64.zip to a temporary folder on your computer.
Open the extracted folder and double-click on the setup.exe file to launch the installation wizard.
On the welcome screen, click Next to continue.
On the license agreement screen, read the terms carefully and click I accept the terms in the license agreement if you agree with them. Then click Next to continue.
On the destination folder screen, choose the folder where you want to install IBM DS Storage Manager 10 or accept the default folder. Then click Next to continue.
On the setup type screen, choose the type of installation you want to perform. You can choose Typical, Custom, or Complete. Typical installs only the GUI and CLI components. Custom allows you to select which components you want to install. Complete installs all the components including GUI, CLI, SNMP agent, and CIM agent. For this article, we will choose Complete. Then click Next to continue.
On the ready to install screen, review your installation settings and click Install to begin the installation.
Wait for the installation to complete. You will see a progress bar and a status message.
When the installation is complete, you will see a completion screen. Click Finish to exit the wizard.
How to configure IBM DS Storage Manager 10?
To configure IBM DS Storage Manager 10 for your IBM System Storage DS3000 series devices, you need to follow these steps:
Launch IBM DS Storage Manager 10 from your Start menu or desktop shortcut.
You will see a login screen. Enter your user name and password for your storage subsystem or accept the default values (user name: manage, password: !manage). Then click OK to login.
You will see a discovery screen. Click Discover Subsystems to scan for available storage subsystems on your network or click Add Subsystems Manually to enter the IP address or host name of your storage subsystems. Then click OK to add them to your management console.
You will see a main window with a tree view of your storage subsystems and logical drives on the left pane and a graphical view of your storage subsystems and logical drives on the right pane. You can use the toolbar buttons or the menu options to perform various tasks such as creating arrays and logical drives, assigning host ports and mappings, enabling premium features, performing copy services operations, monitoring the status and performance of your storage subsystems and logical drives, configuring event notification and logging settings, updating firmware and device drivers, importing and exporting arrays, performing diagnostics and troubleshooting, and more.
How to use IBM DS Storage Manager 10?
To use IBM DS Storage Manager 10 for your IBM System Storage DS3000 series devices, you need to familiarize yourself with some of the basic concepts and terms used by the software. Here are some of them:
Storage subsystem
A storage subsystem is a physical device that contains one or more controllers, power supplies, fans, batteries, drive bays, host ports, expansion ports, and management Ethernet ports. It provides storage capacity and data protection for your hosts. You can connect up to four expansion units to a storage subsystem to increase its storage capacity.
Controller
A controller is a component of a storage subsystem that manages the data flow between the hosts and the drives. It also performs RAID calculations, cache management, copy services operations, event notification, logging, firmware updates, diagnostics, and troubleshooting. Each storage subsystem has two controllers that operate in an active-active mode for load balancing and failover purposes.
Array
An array is a logical grouping of one or more physical drives that are managed by a controller. An array can be configured with different RAID levels depending on your performance and data protection requirements. You can create up to 16 arrays per controller.
Logical drive
A logical drive is a logical partition of an array that is presented to a host as a single unit of storage. A logical drive can be formatted with different segment sizes depending on your performance and alignment requirements. You can create up to 64 logical drives per array.
Host port
A host port is a physical port on a controller that connects to a host or a switch. It can be configured with different speed and topology settings depending on your connectivity and compatibility requirements. You can use up to four host ports per controller.
Mapping
A mapping is a logical association between a logical drive and a host port. It determines which logical drives are accessible by which hosts or host groups. You can create up to 256 mappings per controller.
Premium feature
A premium feature is an optional feature that enhances the functionality and performance of your storage subsystem. It requires a license key to activate. Some of the premium features are volume copy, flash copy, remote mirror, enhanced remote mirror, and partitioning.
Copy services
Copy services are operations that create copies of data from one logical drive to another for backup, recovery, or migration purposes. They can be performed either locally or remotely depending on the type of copy service. Some of the copy services are volume copy, flash copy, remote mirror, and enhanced remote mirror.
Event notification
Event notification is a feature that alerts you of any critical or informational events that occur on your storage subsystem. You can configure the event notification settings to send email messages, SNMP traps, or CIM indications to your designated recipients.
Logging
Logging is a feature that records the history of events, commands, and performance data on your storage subsystem. You can configure the logging settings to specify the level of detail, the frequency, and the destination of the logs. You can also view, export, or delete the logs as needed.
A table comparing IBM DS Storage Manager 10 with other storage management software
SoftwareSupported devicesSupported operating systemsSupported protocolsSupported features
IBM DS Storage Manager 10IBM System Storage DS3000 seriesWindows Server 2003/2008 (64-bit), Linux (32-bit/64-bit), Solaris (32-bit/64-bit), AIX (32-bit/64-bit), HP-UX (32-bit/64-bit), VMware ESX Server (32-bit/64-bit)SAS, SATA, iSCSI, FCGUI, CLI, SNMP agent, CIM agent, array management, logical drive management, host port management, mapping management, premium feature management, copy services management, event notification management, logging management, firmware update management, device driver update management, array import/export management, diagnostics and troubleshooting management
Dell OpenManage Storage Services (OMSS)Dell PowerVault MD3000 seriesWindows Server 2003/2008 (32-bit/64-bit), Linux (32-bit/64-bit), Solaris (32-bit/64-bit), VMware ESX Server (32-bit/64-bit)SAS, SATAGUI, CLI, SNMP agent, CIM agent, array management, logical drive management, host port management, mapping management, copy services management, event notification management, logging management, firmware update management, device driver update management, diagnostics and troubleshooting management
HP StorageWorks Modular Smart Array (MSA) System Management Utility (SMU)HP StorageWorks MSA2000 seriesWindows Server 2003/2008 (32-bit/64-bit), Linux (32-bit/64-bit), Solaris (32-bit/64-bit), VMware ESX Server (32-bit/64-bit)SAS, SATA, iSCSI, FCGUI, CLI, SNMP agent, CIM agent, array management, logical drive management, host port management, mapping management, copy services management, event notification management, logging management, firmware update management, device driver update management, diagnostics and troubleshooting management
Conclusion
In this article, you have learned what is IBM DS Storage Manager 10, why you need it, and how to download it for your Windows Server 2003 or 2008 (64-bit) operating system. You have also learned how to install, configure, and use the software to manage your IBM System Storage DS3000 series devices. You have also seen a table comparing IBM DS Storage Manager 10 with other storage management software. We hope that this article has been helpful and informative for you. If you have any questions or feedback, please feel free to contact us.
FAQs
Q: What are the system requirements for IBM DS Storage Manager 10?
A: The system requirements for IBM DS Storage Manager 10 are:
A Windows Server 2003 or 2008 (64-bit) operating system with the latest service pack and updates.
A minimum of 1 GB of RAM and 500 MB of free disk space.
A network connection to your storage subsystems and hosts.
An IBM ID to download the software from the IBM Support website.
A license key to activate the premium features.
Q: How can I update the firmware and device drivers of my storage subsystems and hosts?
A: You can update the firmware and device drivers of your storage subsystems and hosts by using the Update Firmware Wizard and the Update Device Driver Wizard in IBM DS Storage Manager 10. You can access these wizards from the Tools menu or the toolbar buttons. You will need to download the latest firmware and device driver packages from the IBM Support website before using these wizards. You will also need to follow the instructions and precautions provided by the wizards.
Q: How can I perform diagnostics and troubleshooting on my storage subsystems and logical drives?
A: You can perform diagnostics and troubleshooting on your storage subsystems and logical drives by using the Diagnostics Wizard and the Troubleshooting Wizard in IBM DS Storage Manager 10. You can access these wizards from the Tools menu or the toolbar buttons. You will need to select the storage subsystems or logical drives that you want to diagnose or troubleshoot, and follow the instructions and options provided by the wizards. You will also need to collect a support bundle on critical events that can be used for further analysis.
Q: How can I import and export arrays between different storage subsystems?
A: You can import and export arrays between different storage subsystems by using the Import Array Wizard and the Export Array Wizard in IBM DS Storage Manager 10. You can access these wizards from the Tools menu or the toolbar buttons. You will need to select the source and destination storage subsystems, and the arrays that you want to import or export. You will also need to ensure that the source and destination storage subsystems have compatible firmware versions, RAID levels, segment sizes, premium features, etc.
Q: How can I contact IBM Support for assistance?
A: You can contact IBM Support for assistance by using the Contact Support Wizard in IBM DS Storage Manager 10. You can access this wizard from the Help menu or the toolbar button. You will need to provide your contact information, your storage subsystem information, your problem description, and your support bundle file. You will also need to select your preferred method of communication (phone or email) and your preferred language. The wizard will then connect you to an IBM Support representative who can assist you with your issue. dcd2dc6462